The only problem I've got is the Wi-Fi. Mike -- On 29/12/13 02:26, Mark Rijckenberg wrote: > Your question #241333 on Ubuntu changed: > https://answers.launchpad.net/ubuntu/+question/241333 > > Status: Open => Answered > > Mark Rijckenberg proposed the following answer: Or can/must it stay?? I've tried installing the drivers, but the sytem says it doesn't find any. have a peek at this web-site
It does also seem that yes, the driver can be updated with no need to rebuild the whole kernel. lcpci -nn | grep 0280 returned 01:00.0 Network controller : Qualcomm Atheros AR9485 Wireless Network Adapter [168c:0032] (rev 01) –Usman Jan 9 '14 at 9:52 add a comment| 1 Answer 1 Then I found the Linux Wireless ath9k page, where there was a list of supported chipsets with the following entry: AR9485 (>= 2.6.39) 1x1 SB 11n PCIe I don’t know what inet:127.0.0.1 Másc:255.0.0.0 Dirección inet6: ::1/128 Alcance:Anfitrión ACTIVO BUCLE FUNCIONANDO MTU:65536 Métrica:1 Paquetes RX:2977 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:2977 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:0 Bytes RX:397158 (397.1 KB) TX bytes:397158
The target `modules' must be reprocessed. Highlight the diagnostic command written on the page. Mike (maperry) said on 2013-12-28: #3 Firstly: My thanks for coming to my call for help.
You should decide what desktop environment you want and choose your variant based on that (Ubuntu for Unity, Kubuntu for KDE, Xubuntu for XFCE, Lubuntu for LXDE). A speedtest.net check showed a 90% lower speed on my kubuntu. According to this link http://www.tomshardware.co.uk/answers/id-1848077/acer-aspire-522-wireless-status-button-front-red-press.html you need to press Fn-F3, not simply F3. Is it the wrong version?
Unsubscribe from ThePhoenixYOLO? Check This Out After re-booting bring up the interface.
sudo ifdown wlan0; sudo ifup wlan0;
It should look like this: 8. Afterwards checke the file by finding it with Nautilus and reading it. Obviously it didn't work.
Described below is a workaround to fix this problem in Ubuntu/Kubuntu Natty Narwhal.Create a new file /etc/modprobe.d/ath9k.conf: sudo nano /etc/modprobe.d/ath9k.conf Add the following line to it:options ath9k nohwcrypt=1Save and reboot. Mike (maperry) said on 2013-12-29: #13 Mark, Thanks. The switch (right) is at off and cannot be set to ON. http://tbapplication.com/atheros-ar9485/atheros-ar9485-driver-windows-7.html Thank you yet again so much!
Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 064e:d213 Suyin Corp. Device 83ad Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation NM10 Family LPC Controller (rev 02) UbuntuLive 488,505 views 3:36 GUI Program to install ath9k_htc (Atheros Linux Driver) - Ubuntu Lucid - Duration: 2:49.
An initial cursory check of the WiFi card by attemping to receive signals from neighbouring WiFi routers failed and alerted me to the problem. now go back to /etc/network/interfaces and remove (or comment out with a # in front the wpa-ssid, and wpa-pskid for the wlan card. Transcend StoreJet 25M3 Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub ##### PCMCIA Card Info ##### ##### rfkill ##### 0: phy0: Wireless LAN Soft blocked: yes Hard blocked: The card interface is STILL not up! 5.
What else then? Facebook Twitter Google Plus ReddIt Email WhatsApp Home ServerHow to fix Atheros AR9285 / AR9287 wireless problems in Ubuntu Natty Narwhal?May 8, 2011Anand224 Views I recently installed Kubuntu Natty Narwhal 64 The connection is not enabled and when I toggle it on from my hardware: the "Enable Wi-Fi" option is marked on for a while and then within few seconds toggles off. have a peek here Will try this out and let you know what happened.
I'm not new to Linux, but neither am I a Unix professional and my Latin is exhausted.